 |
| CK1025-4 No. 55 Bit by Cir-Kit |
Price: $1.50
|
| These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood.
The No. 55 bit is used in making starter holes for the CK1023-6 Spring-Loaded eyelets and for the small hollow eyelets used at tape run interconnect points. Measures .052" in diameter.
All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. |
|
|
 |
| CK1014-1 Pilot Hole Punch by Cir-Kit |
Price: $9.96
|
| Pilot Hole Punch with 2 Needles
An essential tape wiring installation tool, the Pilot Hole Punch provides a convenient method of making starter holes for brass brads at all electrical interconnection points. The diameter of the punching tip is smaller than the smallest brad used, thus reducing the risk of punching excessively large holes in the copper foil tape runs. This ensures creation of the correct size hole for positive electrical connection.
The locking chuck provides an easy method of needle replacement in the event of breakage. Overall length is 4-13/16" with a handle diameter of 3/8". (Included in all Cir-Kit Concepts tape wiring kits.) |
|
|
 |
| CK1014-3 Pilot Hole Punch Needles by Cir-Kit |
Price: $1.96
|
| Pilot Hole Punch Needles
Set of 2
The diameter of the punching tip is smaller than the smallest brad used, thus reducing the risk of punching excessively large holes in the copper foil tape runs. This ensures creation of the correct size hole for positive electrical connection. |
|
|
 |
| CK1025 No. 70 Bit by Cir-Kit |
Price: $1.50
|
| These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood.
The No. 70 bit may be used in place of a push pin for making .028" holes in copper tape runs This size hole allows easy bradding of either a 12-volt GOW or wire terminal bulb into a conductive tape run.
All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill.
|
|
|
 |
| CK1025-1 No. 75 Bit by Cir-Kit |
Price: $1.50
|
| These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood.
The No. 75 bit allows drilling of small .021" holes at tape juncture points for easy insertion of 1/8" brads in hardwood or Masonite structures. (May also be used for outlet and switch nails.) The drilling of holes simplifies brad installation and assures a tight electrical fit between the brad and copper strip.
All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. |
|
|
 |
| CK1025-2 1/32 inch Bit by Cir-Kit |
Price: $1.50
|
| These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood.
The 1/32" bit provides the proper size hole for wall sconce wires. This hole allows the pulling of sconce wires through a wall and electrically connecting them into a conductive tape run on the opposite side of a wall. (The wires are inserted into copper strip holes made with either a push pin or No. 70 bit)
All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. |
|
|
 |
| CK1025-3 No. 66 Bit by Cir-Kit |
Price: $1.50
|
| These tiny bits are helpful aids for installing any of the various Cir-Kit Concepts wiring and lighting fixtures. Their use greatly enhances and simplifies installation in all types of wood.
The No. 66 wire-size bit is used principally in the CK104 kit for making the proper size hold for "fixture" and "circuit" type wires. Measures .033" in diameter.
All bits may be used with either a 1/4" electric drill or the CK201 Mini Drill. |
|
|
 |
| CK1041 Brass Head Hammer by Cir-Kit |
Price: $10.96
|
| Brass Head Hammer
The CK1041 hammer, as shown, has been specially designed and manufactured for Cir-Kit Concepts to aid and simplify the brass brad and eyelet installation process. Its size and weight allow easy use in even the most remote corners of a dollhouse.
Only 5-1/2" long, the hammer is made with a solid brass head and a deeply serrated steel handle for a positive grip. The weighted brass head makes it ideal for any number of miniature building projects! |
|
|
 |
| CK1042 Short Nose Pliers by Cir-Kit |
Price: $12.96
|
| Short Nose Pliers
Excellent for holding and inserting 1/8" brass brads in the various tape installation steps, these pliers have proven to be one of the most convenient tools available to the tape wiring installer. No other pliers have the grip and positive feel this one possesses.
Made from special heat-treated steel, the pliers have serrated teeth on both jaws, a self-contained spring for easy opening and plastic-coated handles for comfortable holding. Good for a hundred and one different uses. A "must" for any mini-electrician!
Product style may vary. |
|
|
 |
| CK1043 Swivel Head Flashlight by Cir-Kit |
Price: $4.96
|
| Swivel-head Flashlight
There is perhaps nothing more frustrating than working inside an unlit dollhouse room. Whether it is during the construction process or when wiring, it is no fun working in the dark. That is where our new swivel-head flashlight comes to the rescue. This unique device with its rotating head, small size, and bright, wide beam makes it the perfect answer for lighting even the smallest of dollhouse rooms. Simply place in the room and point in any direction where illumination is required. Its compact size makes it easy to carry in either a pocket or purse. An attached clip on the back also makes it convenient to carry on a belt. Use this uniquely styled flashlight in your car, at the office or in your home; where a quick, bright light is required.
Measures 3-1/8" high by 1-5/8" wide by 3/4" deep. Requires two easily replaceable AA batteries, not included |
|
|
 |
| CK1044 Awl by Cir-Kit |
Price: $10.96
|
| Awl
This tool has been designed specifically for placement of the CK1023 series of eyelets. The awl is first used to make starter holes where eyelets are desired. The eyelet is then slipped over the awl insertion pin and pushed into place. It provides an extremely simple method of making electrical connections in hard to reach dollhouse locations.
Made with a rugged wood handle formed to comfortably fit the hand. A hollow compartment in the metal shank provides convenient storage for the four insertion pins. Both shank and punch are nickel plated. Overall length is approximately 4-5/8". Instructions in package.
|
|
|
 |
|
 |
| CK1046 5 inch Locking Forcepes w/Curved Tip by Cir-Kit |
Price: $7.96
|
| 5 inch Locking Forcepes w/Curved Tip
These forceps provide a significant advancement in the brass brad insertion process. Their locking handles and fine serrated teeth allow easy gripping and holding of 1/8" brass brads in even the most awkward locations. Made of surgical stainless steel these tools are ideal for home or shop workbench. Overall length 5". |
|
|
 |
| CK1046-1 5 inch Locking Forcepes w/Straight Tip |
Price: $7.96
|
| 5 inch Locking Forceps w/Straight Tip
These forceps provide a significant advancement in the brass brad insertion process. Their locking handles and fine serrated teeth allow easy gripping and holding of 1/8" brass brads in even the most awkward locations. Made of surgical stainless steel these tools are ideal for home or shop workbench. Overall length 5". |
|
|
 |
| CK1050 Jewelers Screwdriver Set by Cir-Kit |
Price: $4.96
|
| Jewelers Screwdriver Set
This set of five nickel-plated jewelers screwdrivers is a must for installing or removing any small gauge screw. They have been designed with heads that swivel and blades that are permanently affixed to a knurled handle. Shaft blades range from widths of .049" to .079" with overall lengths between 3" and 3-3/8". |
|
|
 |
| CK1051 Bulb Extractor by Cir-Kit |
Price: $3.96
|
| Bulb Extractor
At last a tool to eliminate the maddening task of screw bulb removal. Some chandeliers are designed in such a manner as to make bulb removal nearly impossible. The CK1051 Bulb Extractor simplifies this effort and makes light work out of a previously difficult task. Simply slide down over bulb, twist it and remove the bulb. Flexible teeth adjust to grip the wide variances that exist in bulb design and manufacture. The hollow rubber tip on the opposite end may be used for gripping bulbs when only the tips are exposed. It may also be removed for tight access locations. Nickel plated, brass construction assures a lifetime of satisfactory operation.
Use with all screw-base type flame-tip bulbs. |
|
|
 |
| CK1052 Wire Stripper by Cir-Kit |
Price: $1.96
|
| Wire Stripper
Use this handy wire stripper for stripping CK203-1 speaker type 24 gauge wire. Simply clip over wire, compress teeth and pull. Illustrated instructions included with each package. |
|
|
 |
| CK1053 Low-Voltage Soldering Iron by Cir-Kit |
Price: $14.96
|
| Low-Voltage Soldering Iron
Our low-voltage soldering iron works with any 10 watt or larger 12-volt Cir-Kit Concepts transformer or 12-volt car battery. Heats to solder melting temperature in 3 to 4 minutes. Safest soldering iron yet. Use with CK1033-1 solder. |
|
|
 |
| CK1054 Brad Placement Tool by Cir-Kit |
Price: $10.96
|
| Brad Placement Tool
Brad Insertion Simplified
Over the years, the use of tapewire has become the predominate worldwide method of dollhouse wiring. Its versatility and ease of installation has made it the dollhouse electricians method of choice. However, to achieve low-profile corners, it is necessary to use tiny 1/8" brass brads to create the necessary electrical interconnection. Although these brads serve this purpose very well, they can be frustrating to hold and install.
That is where our new CK1054 Brad Placement Tool comes in. With this tool, the brad can be held firmly in place as it is inserted into the tape run. No more lost brads or blue language. They are manufactured of stainless steel with a plastic coated handle for a lifetime of operation. The CK1054 should be a must for every tape wiring toolbox.
|
|
|
 |
| CK201 Mini Drill by Cir-Kt |
Price: $10.96
|
| Mini Drill
If you have ever had to drill small holes in hardboard materials you know there has to be a better way. The pin vise method sometimes just is not fast enough. Enter our high-speed drill. This drill has been specifically designed for the hobbyist who must work with all types of material. The overall length is a mere 4-1/2" making it one of the most maneuverable drills available. A 3 to 1 gear ratio gives the drill its fast drilling capability and high torque characteristic. The solid brass chuck is continuously adjustable and accepts all number size bits from 61 through 80. No key is needed since the knurled chuck may be completely tightened by hand. Another distinguishing feature is its hollow handle with threaded cap for storage of bits. |
|
|
 |
| CK204 Test Probe by Cir-Kit |
Price: $5.96
|
| Test Probe
This unique tool eliminates forever the need for making your own electrical tester. Constructed with two sharp needles and a self-contained light bulb, the CK204 Test Probe can be used at any point along a conductive tape run for electrical testing or finding a tape run under wallpaper.
Simply push the needles into the copper strips and, if electricity is present, the enclosed bulb will light. The .175" pin spacing makes this handy tool useable with any tape system. It also provides proper spacing for placement of the eyelets when installing the CK801 Sconce Adapter or the CK804 series of Chandelier Adapters. Comes with snap top safety cap. Overall length approximately 2". |
|
|
 |
| HW2228 Bulb Extraction Tool by Houseworks |
Price: $2.95
|
| Use the slotted metal end to extractcandle flame bulb inside narrow funnel. Rubber end gives traction for either round or flame bulb extraction. (Excessive pressure will break the bulb.) |
|
|
 |
| HW2229 Test Probe by Houseworks |
Price: $5.50
|
| Use the slotted metal end to extractcandle flame bulb inside narrow funnel. Rubber end gives traction for either round or flame bulb extraction. (Excessive pressure will break the bulb.) |
|
|
